How to perform daily maintenance on the aluminum foil slitting machine?

1. Cleaning
1. Body cleaning:
Use a clean soft cloth to wipe the surface of the aluminum foil slitting machine regularly to remove dust and debris. Pay special attention to cleaning the feed port, discharge port and the area around the cutter to prevent the accumulation of aluminum foil debris from affecting the operation of the equipment.
For stains that are difficult to remove, you can use a mild detergent, but avoid using highly corrosive chemical solvents to avoid damaging the surface coating of the equipment.
2. Tool cleaning:
After each use, clean the aluminum foil residue on the cutter in time. You can use a soft brush to gently brush off the debris on the blade, and then wipe it clean with a clean cloth.
Check the wear of the cutter regularly. If the blade is found to be blunt or notched, it should be ground or replaced in time to ensure the quality of slitting.
3. Conveying system cleaning:
Check the conveying system of the slitting machine, including conveyor belts, rollers and other components, and clean the aluminum foil debris and dust on them. You can use compressed air to blow the surface of the conveyor belt, or wipe the roller with a damp cloth.
Ensure that all parts of the conveying system operate flexibly without jamming. If the conveyor belt is found to be worn or the roller is damaged, it should be replaced in time.
2. Lubrication
1. Determine the lubrication parts:
Understand the lubrication requirements of the aluminum foil slitting machine, which usually include the tool shaft, the rollers of the conveying system, and the transmission parts. Refer to the instruction manual of the equipment to determine the lubrication cycle and lubricant type of each lubrication part.
2. Choose the right lubricant:
Choose the right lubricant according to the different lubrication parts. For high-speed running parts such as the tool shaft, high-quality lubricating oil can be used; for the rollers and transmission parts of the conveying system, grease can be used.
Ensure that the quality of the lubricant is reliable and meets the requirements of the equipment to ensure the lubrication effect.
3. Lubricate regularly:
Lubricate the equipment according to the prescribed lubrication cycle. Before lubrication, clean the dust and debris in the lubrication parts to ensure that the lubricant can fully play its role.
Control the amount of lubricant to avoid too much or too little. Too much lubricant may cause equipment pollution and waste, and too little will not achieve a good lubrication effect.
3. Inspection and adjustment
1. Tool inspection:
Regularly check whether the tool is firmly installed and whether the blade is sharp. If the tool is found to be loose, tighten the fixing bolts in time; if the blade becomes blunt, grind or replace it in time.
Check whether the tool gap is appropriate. Too large or too small tool gap will affect the slitting quality, and should be adjusted according to the thickness of the aluminum foil.
2. Transmission system inspection:
Check the transmission system of the slitting machine, including belts, chains, gears and other components, to check whether there is looseness, wear or damage.
For belt drive, check whether the belt tension is appropriate. Too loose or too tight will affect the operating efficiency and stability of the equipment. For chain and gear drive, check whether the meshing is good and whether there is abnormal noise and vibration.
3. Electrical system inspection:
Regularly check the electrical system of the aluminum foil slitting machine, including power cords, switches, controllers and other components to ensure that they are firmly connected and not damaged.
Check whether the grounding of the electrical system is good to avoid safety accidents such as leakage. At the same time, pay attention to the heat dissipation of the equipment to ensure that the electrical components operate within the normal operating temperature range.
4. Adjust equipment parameters:
According to the thickness, width and other parameters of the aluminum foil, adjust the slitting speed, tension control and other parameters of the slitting machine in time. Ensure that the equipment operates in the best condition to improve the slitting quality and efficiency.
When adjusting the parameters, pay attention to the operating status of the equipment. If there is any abnormality, stop the adjustment in time, and check and repair it.
IV. Safety and storage
1. Safe operation:
When using the aluminum foil slitting machine in daily life, strictly abide by the operating procedures to ensure the safety of the operator. The operator must undergo professional training and be familiar with the operation methods and safety precautions of the equipment.
During the operation of the equipment, it is strictly forbidden to put your hands or other objects into the tool area to avoid danger. At the same time, pay attention to whether the safety protection device of the equipment is intact, and repair it in time if it is damaged.
2. Equipment storage:
When the aluminum foil slitting machine is not used for a long time, it should be properly stored. Clean the equipment and apply rust inhibitor to prevent the equipment from rusting.
The equipment should be stored in a dry and well-ventilated place, avoiding direct sunlight and humid environment. At the same time, pay attention to regular inspection and maintenance of the equipment to ensure that the equipment remains in good condition during storage.